Search results for "Stress analysis"

Bone-to-implant contact of orthodontic implants in humans--a histomorphometric investigation

2008

The purpose of the present study was to evaluate the percentage of direct bone-to-implant contact (BIC) of orthodontic anchorage implants (Orthosystem) after active orthodontic treatment. Twenty orthodontic implants (diameter, 3.3 mm; length, 4 or 6 mm) were inserted for orthodontic anchorage in different anatomical regions of 18 adult patients (nine males, nine females) aged 18-63 years. Fifteen implants (one per patient) were placed in the mid-palatal area, one implant (one patient) in the retromolar area of the mandible, one in the retromolar area and the mid-palatal area (one patient), and two (bilaterally, one patient) in the zygomatic area. The duration of the unloaded healing period …

Vertical Mandibular Alveolar Bone Distraction and Dental Implant Placement: A Case Report

2006

Abstract Extensive bone defects complicate the adequate placement of dental implants and the required angulation. In such cases, alveolar-ridge augmentation techniques such as guided bone regeneration, particulate or block grafting, and alveolar bone distraction are needed. The present study describes a case in which a large vertical bone defect in the anterior mandibular zone was corrected via vertical alveolar bone distraction. Six dental implants were posteriorly placed for implant-supported restoration of the mandible, with early implant loading. The clinical and radiologic control showed good implant and soft tissue conditions 12 months later.

ANALISI E SVILUPPO DI UN SETUP SPERIMENTALE PER LA DETERMINAZIONE DELLA TENACITÀ A FRATTURA A MODO II NEI MATERIALI COMPOSITI E IBRIDI

Il presente lavoro di Tesi si propone a compimento del percorso previsto dal Ciclo XXVI del corso di Dottorato di Ricerca in Ingegneria Civile e Ambientale – Indirizzo Materiali – seguito durante il triennio Gennaio 2013- Dicembre 2015 presso l’Università degli Studi di Palermo. L’elaborato si sviluppa in due principali sezioni. Dopo un’introduzione all’argomento affrontato, nella prima parte del lavoro, viene analizzato, sia sperimentalmente che numericamente, un setup tipicamente utilizzato nell’industria aeronautica per la caratterizzazione delle delaminazione a MODO II nei materiali compositi (Transverse Crack Tensile test – TCT-test). A partire dai risultati ottenuti dalle analisi prel…

Determination of polymerization shrinkage stress by means of a photoelastic investigation

2002

This study examined the polymerization stress of different established composite resins (Tetric Ceram, Vivadent; EsthetX, Surefil, Dentsply/DeTrey; Clearfil AP-X, Clearfil Photo Posterior, Kuraray; Prodigy Condensable, sds Kerr; Filtek P 60, 3M ESPE; Solitaire 2, Heraeus-Kulzer) by means of a photo-elastic investigation and investigated six new, experimental composite resins, which have been claimed to exhibit less polymerization shrinkage (InTen-S, Vivadent; K 112, K 051, Dentsply/DeTrey; Compox, Pluto, Hermes 3M ESPE).Cylindrical cavities (phi 5 mm) in Araldit B epoxide resin plates (40 x 40 x 3 mm3) were pretreated with the Rocatec system to ensure bonding of the composite resin. Ten com…

In vitro comparison of the retention capacity of new aesthetic brackets.

1999

Tensile bond strength and bond failure location were evaluated in vitro for two types of aesthetic brackets (non-silanated ceramic, polycarbonate) and one stainless steel bracket, using bovine teeth as the substrate and diacrylate resin as the adhesive. The results show that metallic bracket had the highest bond strength (13.21 N) followed by the new plastic bracket (12.01 N), which does not require the use of a primer. The non-silanated ceramic bracket produced the lowest bond strength (8.88 N). Bond failures occurred mainly between bracket and cement, although a small percentage occurred between the enamel-cement interface with the metal and plastic brackets and within the cement for the …

Support of removable partial dentures in situations with a unilaterally missing canine and a curved edentulous ridge.

1997

The load and movement of abutments and removable partial dentures were examined in situations with a unilaterally missing canine and a curved edentulous ridge. These measurements were performed on a model adapted to intraoral conditions. In this simulation, removable partial dentures supported by incisors may result in failure. Spring rest support results in significantly reduced articulation vertically and horizontally when compared with solid rest support and avoids periodontal overloading.

Shaping ability of nickel-titanium rotary instruments in simulated S-shaped root canals.

2009

Objective The aim of this study was to compare the shaping ability of 4 nickel-titanium rotary techniques and 1 hand technique in simulated S-shaped curved root canals. Study design Seventy-five simulated double-curved resin root canals were divided into 5 groups (n = 15). The canals were compared at 12 different levels and at 3 different times: before preparation and after preparation to master apical 25 and 35. Data were statistically analyzed by performing 2-by-2 comparisons with the Tukey parametric test of variance analysis using a confidence interval of 95%. Results All of the 75 resin blocks presented transportation of the root canals by transforming the apical curvature into a strai…

Finite Element Method and Von Mises Investigation on Bone Response to Dynamic Stress with a Novel Conical Dental Implant Connection

2020

The bioengineering and medical and biomedical fields are ever closer, and they manage to obtain surprising results for the development of new devices. The field of simulations and studies in silica has undergone considerable development in recent years, favoring the advancement of medicine. In this manuscript, a study was carried out to evaluate the force distribution on the implant components (In-Kone® Universal) and on the peri-implant tissues subjected to loading. With the finite element analysis and the Von Mises method, it was possible to evaluate this distribution of forces both at 0 degrees (occlusal force) and at 30 degrees; the applied force was 800 N. The obtained results on this …

Mechanical resistance of zirconium implant abutments: A review of the literature

2010

The increase of aesthetic demands, together with the successful outcome of current implants, has renewed interest in the search for new materials with enough mechanical properties and better aesthetic qualities than the materials customarily used in implanto-prosthetic rehabilitation. Among these materials, zirconium has been used in different types of implants, including prosthetic abutments. The aim of the present review is to analyse current scientific evidence supporting the use of this material for the above mentioned purposes. We carried out the review of the literature published in the last ten years (2000 through 2010) of in vitro trials of dynamic and static loading of zirconium ab…

Osseointegration of miniscrews: a histomorphometric evaluation.

2007

SUMMARY Mini-implants and miniscrews are commonly used in orthodontics to provide additional temporary intraoral anchorage. Partial osseointegration represents a distinct advantage in orthodontic applications, allowing effective anchorage to be combined with easy insertion and removal. This article reports the histomorphometric fi ndings of the osseointegration of bracket screw bone anchors (BSBAs). In an experimental animal study, four BSBAs were inserted in the alveolar process of the lower jaw in each of fi ve male beagle dogs, aged 6.5 months from the same mother. Eleven screws were lost during the study, nine of them due to lack of primary stability. One screw was removed at the end of…